Location:Home - Blogs

Which Factory in China Is Best for Precision Metal Machining?

  • Blogs
  • By: Fengrun Hardware
  • Date: 2026-11-16

Nine out of ten buyers have asked that question. Almost none have asked it correctly.

Because "precision" spans a range so wide that the word on its own means nothing. ±0.1 mm is called precision in sheet metal. ±0.01 mm is routine in CNC machining. ±0.002 mm is where high precision begins. And for optical or semiconductor components, tolerances are measured in microns or fractions of a micron. The same sentence — "we need precision machining" — lands very differently in different factories: quotations can differ fivefold, and the parts produced are not even in the same league.


1. First, Define What "Precision" Means in Your Case

Different precision levels require completely different equipment, processes and inspection. Start by locating yourself:

Band

Typical tolerance

Surface roughness

Process required

Inspection

General machining

±0.05–0.1 mm (IT8–IT10)

Ra 1.6–3.2

Standard CNC milling/turning, sheet metal

Calipers, micrometers

Precision machining

±0.01–0.02 mm (IT6–IT7)

Ra 0.8–1.6

High-rigidity CNC plus finishing operations

Vision system, micrometers, roughness tester

High precision

±0.005 mm (IT5)

Ra 0.4

Grinding (surface / cylindrical / centreless), wire EDM, temperature-controlled shop

CMM, roundness tester

Ultra precision

< ±0.002 mm

Below Ra 0.1

Lapping, honing, mirror EDM, temperature and humidity control, vibration-isolated foundation

High-accuracy CMM, laser interferometer

The critical insight: precision is not produced by good machines alone. It requires machine + process + inspection + environment, all four in place. Miss one, and the tolerance on the drawing is just a number.

  • Machines without process: you can mill to ±0.01 mm, but geometric tolerances (coaxiality, parallelism) will not hold;

  • Process without inspection: you cannot tell a good part from a bad one;

  • Inspection without environment: day-to-night temperature swings alone will move a 300 mm aluminium part by 0.01 mm.



2. Four Hard Indicators of Whether a Factory Can Hold Precision

2.1 Equipment: configuration and condition matter more than the brand plate

Two machines both labelled "machining centre" can differ by three grades: linear scales with full closed-loop feedback or not, spindle thermal compensation or not, positioning accuracy of 0.005/300 mm or 0.01/300 mm, three years old or thirteen.

Questions to ask: machine brand and model, year of purchase, presence of linear scales, measured positioning and repeatability accuracy, spindle speed and rigidity, and whether there is a temperature-controlled shop (20 ±2 °C or 20 ±1 °C).

2.2 Inspection: the accuracy class of the CMM matters more than its existence

Many factories say "we have a CMM". But CMMs have classes too: an MPE of 1.8 + L/350 μm and one of 3.5 + L/1000 μm are not measuring the same things. And a CMM must sit in a controlled-temperature room, or the numbers it produces cannot be trusted by anyone, including its owner.

Questions to ask: CMM model and accuracy specification, whether it sits in a controlled-temperature room, calibration cycle and certificates, whether geometric tolerance reports can be issued, and whether roundness testers, roughness testers and vision systems are available.

2.3 Process: can the factory correct out-of-tolerance parts itself?

The difficulty in precision work usually appears at the last operation: distortion after heat treatment, clamping stress on thin walls, tool deflection in deep cavities. A factory with grinding capability can bring the part back; one without it can only rework or scrap.

Questions to ask: are there surface, cylindrical or centreless grinders? Wire or sinker EDM? Is heat treatment done in-house or subcontracted — and if subcontracted, who owns the distortion risk?

2.4 Process capability: CPK, not "pass rate"

The real measure of a precision shop is consistency at volume. Getting the first ten pieces right is not difficult. Holding the middle of the tolerance band across 5,000 pieces is capability.

Questions to ask: can you provide CPK reports on critical dimensions? Is CPK above 1.33? (1.33 is the entry threshold in automotive; 1.67 is where performance becomes genuinely strong.)


3. Why Precision Parts Cost More: Where the Money Goes

Buyers are often puzzled that the same small aluminium part is quoted at 80 yuan by one factory and 25 by another. The difference sits in five places:

  1. High labour content — conservative cutting parameters (to avoid chatter and deflection) mean slower feed rates and two to three times the cycle time;

  1. Setups and programming — multi-face work needs multiple setups, each one a risk to both time and precision; programming and proving-out is a fixed cost that is brutal on small batches;

  1. Inspection time — on precision parts, inspection can consume 10–15% of total hours, and full-dimensional first-article reports more;

  1. Scrap rate — thin walls, deep cavities and difficult materials carry inherently high scrap rates, and that cost has to be recovered in unit price;

  1. Downstream operations — heat treatment, grinding, surface finishing, cleaning, clean-room packaging.

So negotiate in the right places: volume, lead-time flexibility, packaging, and design optimisation through DFM. Do not squeeze: tolerances (unless genuinely over-specified), inspection, material grade, or heat treatment process. Save money in the wrong place and it comes back as lot failures.


4. Six Common Traps

     1.Inflated precision claims — "we can hold ±0.005 mm", when in reality it requires cherry-picking parts, running slowly and hand-finishing by a veteran. Mass production exposes it.

     2. Inspection used to mask process weakness — 100% inspection to select the good parts, scrapping the rest, with the scrap rate already priced into the unit cost. Workable at low volume; ruinous at scale.

     3. Small shop taking a big order — agrees at quotation, then subcontracts operations to even smaller shops. Quality degrades layer by layer.

     4. Material substitution — 6061 becomes 6063, 304 becomes 201, S45C becomes ordinary carbon steel. Countermeasure: require the MTC and run spectral verification on critical parts.

     5.Confidentiality that never lands — verbal NDAs while drawings circulate through WeChat groups. Countermeasure: signed NDA plus a documented file-control method.

     6.Lead times promised without checking capacity — precision machines are fully booked in peak season, and a squeezed-in order means your job is deprioritised or subcontracted.



5. Fengrun Hardware's Precision Machining Capability

Fengrun Hardware specialises in custom precision metal components. Our service logic is to match the process to the precision requirement, rather than force every part through one standard route.

  • Process coverage — CNC precision turning (including Swiss-type), CNC milling and mill-turn, precision stamping, sheet metal, die casting, plus associated surface finishing;

  • Precision positioning — ±0.02 mm as standard, ±0.01 mm for precision parts, with high-precision requirements confirmed after evaluating part geometry and material;

  • Inspection — CMM, vision measuring system, roughness tester and hardness tester, with measured reports and CPK data available on critical dimensions;

  • Engineering involvement — DFM review on receipt of drawings, identifying which tolerances are functionally necessary and which are over-specified (over-specification is the number one cause of inflated precision-part costs);

  • Volume strategy — CNC for flexible small batches, with a shift to stamping or die casting evaluated at higher volumes, so customers get the right balance between precision and cost.

Workflow: drawing enquiry (2D/3D + material + quantity + precision requirement + finishing) → DFM feedback and quotation within 24–48 hours → sampling with inspection data → first article inspection (FAI) → pilot run → mass production and delivery.