Location:Home - Blogs

China Precision Non-Standard Hardware Parts Processing Factory

  • Blogs
  • By: Fengrun Hardware
  • Date: 2026-11-19

There is one category of order that everyone in metalworking agrees is the hardest to take: the drawing is non-standard, but the tolerances are precision-grade.

Custom work is hard because every order is different — new programming, new tooling, new process validation each time. Precision work is hard because every piece must be identical — tolerances measured in hundredths of a millimetre, with no drift between lots. Put the two together and most factories drop out: shops that can handle custom work cannot hold precision, and shops that can hold precision see custom work as too fragmented to schedule.

What Fengrun does is hold both ends at once.

We are a precision custom hardware parts manufacturer in China, taking a part from drawing review through to volume delivery within one system. This page sets out who we are, what we can make, how we keep quality stable, and which orders are the best fit for us.



1. The Problem We Are Actually Solving

People who buy custom parts tend to get worn down by the same three things.

First, finding a factory that can make it. Drawings go out and either nobody quotes, or the shop accepts and only then discovers that thin walls distort, deep cavities cause tool deflection, or dimensions move after heat treatment. Drawings and processes get revised back and forth, and the project slips by weeks.

Second, the sample passes but production fails. A beautiful first article can be cherry-picked; by part 500, dimensions start drifting. That is not an attitude problem, it is a capability problem — the factory has no CPK control and relies on 100% inspection to sort out the good ones.

Third, too many suppliers and nobody owning the outcome. CNC at one shop, heat treatment at another, anodising at a third, assembly in your own plant. When something goes wrong, all three point at each other and the buyer becomes the coordinator.

Fengrun's service model is built against exactly these three: engineering judgement upfront to settle what can be made and how to make it economically; data during production to control consistency; and one source factory accountable for the final result.



2. Who Fengrun Is

Item

Detail

Positioning

China-based precision custom hardware parts manufacturer; a source factory, not a trading or consolidation company

Core capability

Precision CNC machining, Swiss-type turning, precision stamping, sheet metal forming, die casting with secondary machining, grinding and wire forming

Service model

Build to drawing or sample; DFM involvement; sampling → FAI → pilot run → mass production

Quality system

First article inspection (full-dimensional FAI), CPK control on critical dimensions, lot retained samples and traceability, material and finishing reports shipped with goods

Customers

OEMs and component buyers in industrial equipment, automotive and new energy, medical devices, telecommunications, industrial automation

Engagement types

Prototype and small-batch trials, high-mix low-volume, steady volume supply, OEM/ODM




3. Capability Overview: How Far One Drawing Can Travel

The thing custom parts fear most is a break in the process chain. We keep the main operations under one management system, so a drawing does not have to leave the building to become a part.

Processes

Process

Suited to

Strength

Precision CNC turning / Swiss-type

Shafts, pins, fittings, small-diameter long parts, precision threads

High accuracy on small parts, strong lot consistency

CNC milling / mill-turn

Complex geometry, multi-face parts, cavities, mounting blocks

Multiple faces in one setup, reducing cumulative error

Grinding (surface / cylindrical / centreless)

Mating faces, bearing seats, parts requiring correction after heat treatment

Actually holding sub-0.01 mm and geometric tolerances

Wire EDM / sinker EDM

Hard materials, micro-features, narrow slots, mould inserts

High dimensional accuracy and sharp internal corners

Precision stamping

Spring contacts, connecting strips, shields, thin-sheet parts

Cost advantage at volume; in-house tooling allows fast die changes

Sheet metal (laser / bending / welding)

Enclosures, brackets, housings, structural frames

Flexible at small-to-medium volumes, with integrated finishing

Die casting (Al / Zn) + secondary machining

Complex thin-wall parts, integrated structural shapes

Secondary machining on mating faces ensures assembly accuracy

Wire forming / springs

Bent wire parts, retaining clips, elastic elements

Fast changeover for high-mix low-volume work

Materials: carbon steel (Q235 / 45# / S45C), stainless steel (303 / 304 / 316L), aluminium (6061 / 7075 / 5052), copper and brass (H62 / C3604), titanium (TC4), plus precision parts in engineering plastics such as POM and PEEK.

Surface finishing: anodising (with colour options), zinc and zinc-nickel plating, Dacromet, passivation, black oxide, powder coating and painting, heat treatment (quench and temper, carburising, hardening), polishing and lapping.

A note on scope: anodising, electroplating and similar operations requiring environmental permits are performed by long-standing, fixed subcontract partners. We hold those operations to the same acceptance standard as our in-house ones — coating thickness and salt-spray reports ship with the goods, and Fengrun takes single-point responsibility for them. That is what "one-stop" actually means; it does not mean every machine sits in our own building.



4. Holding Precision and Custom Work Stable at the Same Time

4.1 Review first, quote second

Within 24–48 hours of receiving 2D/3D drawings we return DFM feedback covering three things: which tolerances are functionally necessary, which are over-specified (and can be relaxed for real savings), and which features should be redesigned (fewer setups, less thin-wall distortion).

Precision parts are often expensive not because of machining, but because of unnecessary ±0.01 mm callouts on the drawing. This step frequently takes 20% or more out of cost, and it is where we think engineering capability should show up.

4.2 Samples ship with data

Key dimensions are measured and the values travel with the sample — not just a part in a box. That lets you confirm it was produced consistently, rather than selected lucky.

4.3 FAI draws the responsibility line

Before mass production, every dimension on the drawing is inspected and recorded in a written FAI report, confirmed by both parties, alongside the material test certificate (MTC) and finishing reports. Any later dimensional dispute is then settled against the FAI.

4.4 Pilot runs are judged on CPK, not pass rate

Custom parts most often lose control around part 50: tool wear, clamping stress, machine thermal drift, hardness variation between material lots. At pilot stage we run process capability analysis on critical dimensions and only move to mass production at CPK ≥ 1.33, keeping patrol inspection and SPC trend records.

4.5 Traceability across production lots

Retained samples by lot and recorded measured values on critical dimensions, with an OQC report on every shipment. Measured data for any lot from three months ago can be pulled up on request.

4.6 Packaging designed around the transport mode

Individual rust protection (VCI film or rust-preventive oil), compartmentalised inner packing, desiccant and reinforced pallets — an export shipment that opens rust-free and damage-free is the final link in quality, so we count it as part of quality.



5. Why a Source Factory Matters More on Custom Work

Custom parts have no catalogue price and no standard process to copy. Almost every decision has to be made while the job is running: modify a fixture, adjust a parameter, change a tool, add a finishing pass.

  • A trader or consolidator can relay a requirement but cannot change a process on the spot; one adjustment waits on a subcontractor's reply, and the timeline is not controllable.

  • A source factory has engineers, machines and inspection under one roof, so it can trial, adjust and re-measure the same day.

For the customer, the difference shows up in three places: response speed (an answer the same day), cost structure (no intermediary margin, with tooling and programming costs transparent), and accountability (one point of contact, one party responsible).



6. How We Work Together

Step

Activity

Deliverable

1

Send 2D/3D drawings or a sample, with material, quantity, precision and finishing requirements

RFQ

2

DFM manufacturability review (24–48 hours)

Process recommendations and optimisation options

3

Quotation

Itemised quote: material / machining hours / tooling amortisation / finishing / inspection

4

Sampling

Sample plus measured values on key dimensions

5

First article confirmation

Full-dimensional FAI report and material certificate

6

Pilot run

CPK report, patrol inspection records

7

Production and delivery

OQC report, retained-sample records, export documents

Confidentiality: an NDA can be signed; drawings circulate in a controlled environment and are deleted or sealed at project end as required. Tooling ownership is stated explicitly in the contract.



7. Industries We Serve

  • Industrial equipment and automation — custom structural parts, mounting blocks, drive components, jigs and fixtures

  • Automotive and new energy — precision connectors, brackets, housings, battery structural parts (IATF-aligned projects run under the relevant system)

  • Electronics and telecommunications — shielding parts, heat sinks, precision spring contacts, connector hardware

  • Medical devices and instruments — precision stainless and titanium parts, components with demanding appearance and cleanliness requirements

  • Consumer and industrial equipment — enclosures, panels, sheet-metal structures, assembled units



8. Which Orders Are the Best Fit for Fengrun

A strong fit

  • Complex geometry with tight tolerances that other shops are reluctant to quote;

  • High-mix low-volume work where lot stability and traceability still matter;

  • Projects that benefit from engineering input on cost — especially where the drawing is not yet frozen;

  • Buyers tired of coordinating several subcontractors and wanting one factory to own the outcome;

  • Long-term partnerships running from prototype through to volume production.

Worth considering elsewhere

  • A few rough prototypes with loose tolerances — a local job shop is faster and cheaper;

  • Standard fasteners and general hardware — buy off the shelf, no custom work needed;

  • Very high volumes of a single simple stamped part (millions and up) — a dedicated automated line has the cost advantage; we can help evaluate it, but will not pretend to be the best answer.

We state what does not fit because the worst outcome in custom manufacturing is an order accepted and then made badly. Being clear about boundaries is more reliable than taking everything.



9. Frequently Asked Questions

Q: We have only a sample, no drawing. Can you work from that?Yes. We reverse-engineer the sample and issue 2D drawings and a 3D model for your confirmation before machining or tooling. Please also tell us the functional requirements for critical mating dimensions — reverse engineering recovers geometry, not design intent on tolerances.

Q: What is the minimum order quantity?CNC work can start from small batches; tooling-based processes (stamping, die casting) are assessed against economical batch sizes. Give us your annual usage and we will structure a phased quote covering a first trial batch and follow-on volume.

Q: Do you charge for samples?Custom parts normally carry a sampling charge covering programming, tooling and material. It can be refunded once an agreed production volume is reached; the terms are confirmed in writing at quotation stage.

Q: What tolerances can you hold?±0.02 mm as standard and up to ±0.01 mm on precision parts; tighter requirements are confirmed after evaluating geometry, material and inspection method. We do not promise numbers we cannot hold — where grinding or a controlled-temperature environment is required, we say so at DFM stage.

Q: What inspection reports can you supply?Measured values on key dimensions, full-dimensional FAI reports, CPK capability reports, material certificates, and coating thickness and salt-spray reports. Third-party verification (SGS/BV) can be arranged by agreement.

Q: Can we audit the factory?You are welcome. We suggest focusing on four areas: machines actually running, tool and fixture management, the inspection room (CMM and calibration certificates), and work-in-progress plus retained-sample areas. Those four reveal the real management level.

Q: What documents are needed for export?Commercial invoice, packing list and Certificate of Origin as standard; material certificates, inspection reports and RoHS/REACH declarations are available according to destination and customer requirements.



Conclusion

Precision and custom work are, by nature, two demands pulling against each other: one insists that every piece be the same, the other that every order be different.

Fengrun's job is to make both hold within a single system — engineering review removes the uncertainty in the drawing, process data removes the uncertainty in production, and being a source factory removes the uncertainty about who is accountable.

If you have a drawing that other shops have been reluctant to quote, send it over. We will start with a DFM review and process recommendations, and then talk about price.



Fengrun

Precision Custom Hardware Parts Manufacturer in China

Build-to-print · Precision machining · One-stop delivery