Location:Home - Blogs

Custom processing of precision aluminum alloy die castings | Direct Manufacturer

  • Blogs
  • By: Fengrun Hardware
  • Date: 2026-11-20

Precision Aluminum Die Castings — A Full Range of Parts, Made Entirely In-House | Fengrun

One in-house chain, from tooling and casting to CNC machining, anodizing, plating and inspection. Fengrun is a source factory in China — we own the process rather than broker it.

An e-drive housing for a new-energy vehicle, a filter cavity for a 5G base station, a gearbox housing for a power tool, the heat sink of a high-power LED luminaire — very different shapes, wall sections, alloys, tolerance requirements and finishes, yet most of them come from the same process: high-pressure aluminum die casting.

"Every kind" is a demanding claim for a casting supplier. It means answering three questions at once: how many geometries can you form, how many alloys can you run, and how many downstream operations can you finish. A shop that only produces raw castings can serve a narrow slice of the market. Only a supplier that connects tooling, casting, precision machining, surface finishing, inspection and assembly into one chain can genuinely talk about a full range of precision aluminum die castings.

That is what Fengrun does. This page sets out, without slogans, the range of parts we actually produce, our end-to-end process capability, and where our advantages lie.



1. The Range We Produce, by Geometry

Different geometries put very different demands on the die, the casting parameters and the downstream machining. Our production lines are configured around these part families:

Part family

Typical features

Common components

Our capability

Housings / cavities

Internal cavities, sealing faces, mating covers

Motor housings, inverter housings, transmission cases, valve bodies, filter cavities

Slides and core pulls, CNC-finished sealing faces, leak testing and impregnation

Brackets / structural parts

Ribs, mounting feet, assembly loads

Brackets, bases, connectors, mounting arms

Rib and wall-thickness optimization, flow simulation against shrinkage, one-setup machining of assembly holes

Heat-sink parts

Dense fins, thin walls, large surface area

LED heat sinks, power-supply housings, telecom thermal enclosures

Thin-wall filling control, complete fin formation, flatness control on thermal contact faces

Thin-wall complex parts

Local thin sections, multi-cavity, multiple core pulls

Telecom cavities, instrument enclosures, small structural parts

Flow-optimized gating and overflows, multi-cavity dies, vacuum die casting to reduce entrapped air

Precision small parts

Small size, tight tolerances, high volume

Connectors, precision fittings, small drive components

Automated extraction on multi-cavity dies, secondary CNC machining, Cpk process control

Medium and large parts

Large projected area, significant wall variation

Equipment enclosures, battery-pack structural parts, large covers

High-tonnage machines [TBC: clamping force], zoned die temperature control, distortion correction

From small precision parts weighing a few grams up to medium and large housings, anything within our equipment and tooling range is produced under one quality system.



2. The Range by Alloy: The Application Chooses the Material

Casting problems are often material-selection problems in disguise. We work backwards from what the part has to do, rather than running every job in the same alloy:

Alloy

Key characteristics

Fits

How we handle it

ADC12 / GB YL113 family

Excellent fluidity, stable filling, suited to complex thin-wall parts

General housings, brackets, telecom cavities, lighting parts

Our main production grade; spectrometer control of composition and return-scrap ratio per heat

A380 / ADC10 family

Good overall mechanical properties and dimensional stability

Loaded brackets, structural parts, power-tool components

Selected by strength requirement, validated at T1 tool trials

A356 / ZL101A family

High ductility, heat-treatable

Structural parts with strength and elongation requirements

Heat-treated parts assessed for squeeze casting or low-pressure routes

Low-copper alloys (A360 / ADC3 / AlSi10Mg family)

Uniform anodized appearance, minimal color variation

Natural-anodized cosmetic parts, consumer enclosures

Grade locked at the DFM stage, so no alloy change after the die is cut

Heat-treatment-free alloys (AlSi10MnMg family)

Large integrated parts meet properties without T6

Large structural parts, megacasting assessment

Process route and equipment match assessed per part [TBC: capability limit]

One detail we settle during development rather than after tooling: ADC12 contains enough copper that natural anodizing tends to turn dark or mottled. When a customer asks for an anodized cosmetic finish, we proactively recommend a low-copper alloy or a powder / wet-paint route instead of waiting for a failed trial after the die is built. That kind of upstream judgment is the difference between "professional processing" and "casting whatever the drawing says."



3. Process Capability: One Chain, from Tooling to Finished Part

A die casting is never finished when it leaves the machine. Fengrun's advantage is not any single machine — it is that we hold all eight steps below in our own hands, including the anodizing and electroplating operations that most shops outsource:

Step

What we do

What it produces

1. DFM and flow simulation

Review wall uniformity, draft angles, gating and overflow layout, machining allowance; simulate filling, solidification and air entrapment

Process concept, flow-simulation report, manufacturability recommendations

2. Die design and tooling

Die insert material (H13 / SKD61 class), heat treatment, cooling circuits, slides and lifters, multi-cavity layout

Die drawings, tooling register, shot-count life records

3. Melting and charge preparation

Grade-specific charge, degassing, fluxing and dross removal, melt temperature control, OES spectrometer analysis per heat

Heat composition records

4. HPDC forming

Cold-chamber process, clamping-force matching, slow-to-fast shot transition, die temperature control units, vacuum die casting and local squeeze pins where required

Process parameter sheets, first-article and lot records

5. Trimming and conditioning

Gate trimming, deburring, shot / sand blasting, distortion correction where needed

Consistent raw castings

6. Secondary CNC machining

Datums, hole patterns, tapping, sealing and mating faces, with clamping-stress control

Full-dimensional FAI report, Cpk data on critical dimensions

7. Surface finishing (in-house lines)

Powder coating, wet painting, anodizing, electroplating, e-coating, passivation, vacuum impregnation, with thickness and color-panel control

Coating thickness / adhesion / salt-spray records, approved color panels

8. Inspection, assembly and shipping

CMM, X-ray / CT inspection, leak testing, OQC, light assembly, impact protection and VCI anti-corrosion packaging

Inspection reports, lot traceability card, finished goods

The practical value of this chain is a single point of responsibility: how much stock the casting leaves for machining, which datum the machining setup uses, and whether impregnation is needed before finishing are all decided in one process review. The buyer never has to relay messages between a casting shop, a machine shop and a finisher, and there is no blame loop of "the casting was fine, machining ruined it" versus "the porosity was already there."

Anodizing and electroplating are run on our own lines — nothing is subcontracted. These two operations carry high environmental-permit barriers, which is why most factories outsource them. Fengrun built them into our own shop: coating thickness, color consistency and salt-spray performance can be adjusted directly on the line; cosmetic parts do not wait in an outside supplier's queue for a color trial; and any nonconformance can be traced immediately to bath chemistry and process parameters. Add tooling, casting, CNC and inspection on the same site, and "one chain" for us is not a promise about who is accountable — it is eight operations literally running on one line. One window for the customer, with lead time and quality unaffected by an outside supplier's schedule.



4. Where the "Precision" Comes From: Dimensions and Internal Soundness

A precision aluminum die casting has to win on two fronts: external dimensions and internal soundness. We have dedicated controls for both.

External dimensions

Item

Our approach

As-cast dimensions

Die accuracy, stable die temperature, controlled ejection and shrinkage, managed to the relevant GB/T 6414 / ISO 8062 grade

Critical dimensions

Assembly datums, bearing bores, sealing faces and tapped-hole pilots always left for secondary CNC machining; ±0.02–0.05 mm class is routinely achievable [TBC: confirm per part]

Consistency

Process-capability studies on critical dimensions; Cpk ≥ 1.33 before ramp-up — process stability, not 100% sorting

Distortion control

Clamping-stress control on thin walls and large flat faces, zoned die temperature, straightening operations where required

Internal soundness

Molten aluminum fills the cavity at high velocity in HPDC, and cavity air can be entrapped as gas porosity — an inherent characteristic of the process. Fengrun controls it at the process end instead of sorting parts afterwards: flow-simulated gating and overflows, vacuum valve evacuation, ultra-slow fill transition, local squeeze pins for feeding, die temperature control units, and melt degassing and fluxing, backed by X-ray / CT interpretation and vacuum impregnation where needed.

That is what lets us deliver leak-tight housings, valve bodies and water-jacket parts consistently. For parts requiring T6 heat treatment or welding, we propose vacuum die casting, squeeze casting or low-pressure casting at the development stage, so blistering and weld defects do not appear after ramp-up. Raising these boundaries before the die is cut, and offering a workable alternative, is part of our engineering support.



5. Surface Finishing: From Structural Parts to Cosmetic Parts

The same raw casting can end up in completely different applications depending on its finish. Every process below runs on Fengrun's own surface-finishing lines, including the anodizing and electroplating operations that carry higher environmental-permit barriers, and can be specified directly for the part:

Process

Fits

Controls we provide

Powder coating / wet painting

Enclosures, brackets, equipment covers; conceals flow marks and parting lines

Pretreatment, film thickness, adhesion, approved color panels, agreed salt-spray hours

Anodizing (in-house)

Cosmetic parts needing a metallic look and wear resistance

Alloy compatibility review first, low-copper grades, colorable, color variation and bath chemistry managed in-house

Electroplating (in-house)

Parts needing conductivity, corrosion resistance or a decorative plating

Plating type and thickness configured to requirement; adhesion and salt-spray records supplied per lot

E-coating / passivation

Corrosion resistance, conductivity, or a base for painting

Film-thickness uniformity, corrosion-resistance records

Shot / sand blasting

Surface texture, or preparation for coating

Roughness and approved appearance samples

Vacuum impregnation

Leak-tight housings, valve bodies, parts with fluid channels

Piece-by-piece leak retest after impregnation

Grinding and polishing

Local cosmetic faces and mating faces

Work instructions that protect datum surfaces

For cosmetic parts we seal an approved golden sample and color panel, and every subsequent lot is judged against them, so a part made months later still looks like the same product.



6. Industries and Typical Parts

Our capability is configured around downstream industries; each cares about different things, and each gets a different process emphasis:

Industry

Typical die castings

What matters

Our capability

Automotive / new energy

E-drive housings, inverter housings, battery-pack structural parts, transmission cases, steering components

Leak tightness, dimensional stability, lot consistency, traceability

Vacuum die casting, impregnation plus piece-by-piece leak testing, Cpk control, full heat / shot / lot traceability

Telecom

5G filter cavities, base-station thermal enclosures, chassis

Complex thin-wall cavities, flatness of thermal faces, appearance

Multi-core-pull dies, flow simulation, CNC finishing of sealing and thermal faces

Power tools

Gearbox housings, motor housings, handle brackets

Strength, assembly accuracy, impact resistance

Alloy selected for load, assembly holes completed in one setup

LED lighting

Heat sinks, luminaire housings

Complete fin formation, thermal-face contact, appearance

Thin-wall filling control, flatness control, coating in-house

Appliances / consumer

Structural enclosures, internal brackets, decorative parts

Appearance consistency, color variation, cost

Multi-cavity dies, approved color panels, automated part extraction

Medical instruments / industrial equipment

Instrument enclosures, structural parts, precision fittings

Dimensional stability, cleanliness, high-mix low-volume

Flexible lines, precision CNC, retained lot samples

General machinery

Valve bodies, pump housings, connectors

Leak tightness, pressure resistance, corrosion

Impregnation, leak testing, anti-corrosion finishes



7. Six Advantages of Working with Fengrun

The capability above boils down to six reasons customers choose us:

Advantage

What it means in practice

1. Tooling in-house, faster development

Own die design and manufacturing, flow simulation upfront; die modifications, repairs and trials do not wait on an outside supplier's schedule, so development cycles and later iterations are significantly shorter

2. Every operation in-house, one point of responsibility

Tooling → casting → trimming → CNC machining → surface finishing (including our own anodizing and electroplating lines) → inspection and assembly all happen inside Fengrun's shop, with no outsourced scheduling to work around and one window for the customer

3. Precision and soundness controlled together

Critical dimensions secured by CNC and Cpk; internal porosity suppressed by vacuum casting, flow simulation and melt treatment; X-ray / CT and leak testing run as standard

4. Flexible order profile

Volume production as well as custom, high-mix low-volume work; drawings, 3D files or physical samples can all be the starting point

5. Full traceability

Heat number, die shot count, machining lot, finishing lot, retained samples and inspection records kept as a set, so a lot issue can be traced to a specific step

6. Engineering involvement upfront

DFM-stage recommendations on wall thickness, draft, alloy, process route and machining allowance — problems solved before the die is cut



8. How a Project Runs

From drawing to volume production, every step has a defined output and visible progress:

Step

What we do

What you receive

1. Requirement and drawing review

Analyze geometry, material, tolerances, leak-tightness and appearance requirements

DFM feedback and process-route recommendation

2. Concept and quotation

Preliminary flow assessment, die concept, definition of machining and finishing scope

A clear development and unit-price proposal

3. Tooling development

Die design, manufacturing, flow validation

Die drawings and development schedule

4. T0 / T1 tool trials

Trials, full-dimensional inspection, X-ray / CT interpretation, leak verification

Sample parts plus inspection data

5. FAI and golden sample

First article inspection, sealed appearance sample and color panel

A jointly approved acceptance baseline

6. Pilot run and ramp-up

Cpk validation, process freeze, lot traceability activated

Consistent production parts

7. Ongoing delivery

OQC, retained samples, protective packaging, lot-by-lot delivery

Finished parts with complete reports and continuing support



9. Frequently Asked Questions

Q1: Can you work from a drawing, a 3D file, or just a physical sample?All three. Drawings and 3D files go straight into DFM review; where only a sample exists, we reverse-engineer it into a model, give manufacturability recommendations, and then develop the die.

Q2: Which aluminum alloys can you cast?Mainly common die-casting grades such as ADC12 / YL113 and A380 / ADC10, with A356, low-copper alloys and heat-treatment-free alloys available where strength, leak tightness, heat treatment or anodizing require them. The grade is locked at the proposal stage.

Q3: What are your minimum wall thickness and maximum part size?We generally recommend 1.5–2.5 mm with uniform walls; locally thinner sections are assessed against part size and flow-simulation results. Maximum part weight and projected area depend on our clamping-force configuration [TBC: specific parameters]. We give a definite answer against the actual drawing.

Q4: What tolerances can you hold on critical dimensions?The as-cast part provides the shape; assembly datums, bearing bores and sealing faces are secured by secondary CNC machining. ±0.02–0.05 mm class is routinely achievable, with each tolerance confirmed during review.

Q5: Can cosmetic parts be natural anodized?Yes. Anodizing is our own line, so color trials, color-variation adjustment and thickness control all happen in-house. An alloy compatibility review comes first: common high-copper grades tend to show visible color variation after anodizing, so we recommend a low-copper alloy or a powder / wet-paint route, decided before tooling starts.

Q6: How do you guarantee leak-tight housings and valve bodies?Vacuum die casting and flow optimization to reduce entrapped air, vacuum impregnation where needed, then piece-by-piece leak testing with the data retained. This is one of our larger part categories.

Q7: What if the part needs T6 heat treatment or welding?Conventional HPDC contains entrapped gas that expands during solution treatment and causes blistering. We assess vacuum die casting, squeeze casting or low-pressure casting at the development stage, or adjust the design, so the performance requirement is met.

Q8: Who builds the die, and who owns it?We design and manufacture it. Ownership, expected die life in shots, repair and storage responsibilities, and die transfer conditions can all be specified in the contract.

Q9: How long from drawing to sample to production?It depends on die complexity and the number of review rounds [TBC: specific lead times]. Our sequence is DFM and flow feedback first, then confirmation of the plan and schedule — this keeps rework inside the development stage.

Q10: Can we order raw castings only, or CNC machining only?Yes. We deliver the full route from tooling to finished part, and also support customers who only want a single step handled for their own production line.